Technician- Maintenance II USA (1st Shift)

Basic Job Functions:

Performs, as directed, all necessary maintenance of the facility, equipment, and grounds, in a timely and cost-efficient manner.

Education/Experience:

• High school diploma/GED and 3+ years maintenance experience OR
• High school diploma/GED and 5+ years of experience in a related field OR
• High school diploma/GED and 2-year technical school & 3+ years’ experience
• Journeyman’s Card from an accredited apprentice ship program preferred.

Required Skills/Competencies:

• Knowledge of manufacturing equipment.
• Knowledge of computer applications (Word, Excel, Outlook).
• Knowledge of CMMS is a plus but not required if coming in from the outside. Internal candidates need to know the CMMS system.
• Project Leader experiences a plus.
• Proven Communications Skills
• Ability to read prints and suggest modifications as required.
• Proven Electro/Mechanical skills.
• Knowledge of Electrical, Mechanical, Vacuum Systems and Robotic.
• Ability to follow Safe Work Practices.
• Full understanding of LOTO
• Ability to work independently with no supervision.
• Capable of troubleshooting to the systems level.
• Full knowledge of all PM’s
• Must be capable of pulling reports and entering data or pass downs into/from the CMMS system.

Essential Responsibilities:

• Accomplishes daily assignments as scheduled and as directed.
• Performs the on-site service and repair of equipment.
• Must meet at least 90% of Estimated Repair Times
• Interfaces with other departments.
• Follows standard OSHA, EPA, and Company safe practices on all work assignments.
• Identifies and recommends opportunities for cost savings.
• May be asked to train other employees.
• If no tech III is available may be asked to fill in as Team Lead.
• Ability to read electrical & mechanical drawings and technical manuals.
• Performs other assignments as required.
• Responsible to manage waste generated from any work that is performed.

This includes but is not limited to:

• Remove hazardous waste HEPA filters / pre filters and put in proper bags and then put into properly labeled gay lords. And clean up the area after work is done.
• Transport the full gay lords to the North Waste Cage. Contact WWT Associates when dropping off Gaylord.
• Make sure Gaylord is properly label and dated. Work with WWT Associates and/or EHS to make sure the gay lords is properly labeled.
• Move full AED drums back to the North Waste Cage. Make sure drum is properly labeled and dated. Drum cannot be over 882 lbs. Work with WWT Associates and/or EHS to make sure the drum is properly labeled.
• Responsible for adherence to all safety procedures, good housekeeping standards, and the wearing of PPE.
• Notify EHS Department if there are questions or concerns with the management of hazardous waste.

Reporting Relationships:

• This position will not have direct reports.
• If hiring to a new plant prior to plant start, associate will be required to spend extended time (60-80%) in another plant in either Ohio or Alabama for training until their assigned plan starts equipment installation.

Estimated Salary Range:

• $21.97 - $30.77 Hourly

US Physical Requirements:

Manufacturing & Maintenance Physical Requirements:

• Will sit, stand or walk short distances for up to 12 hours per day.
• Will climb stairs on an occasional basis.
• Will exert up to 58 pounds of force to lift, push or pull on a seldom basis.
• Will lift, push or pull up to 27 pounds on a frequent basis.
• Will lift up to 58 pounds on an occasional basis, according to work instructions.
• Will lift up to 37 pounds on a frequent basis.
• Will push or pull up to 27 pounds of force on an occasional basis.
• Will push or pull up to 10 pounds of force on a frequent basis.
• Required to use hands to grasp, lift, handle, carry or feel objects repetitively on a frequent basis.
• 20/40 vision in each eye, with or without correction, is required.
• Must be able to comply with all safety standards and procedures.
• May reach above shoulder heights and below the waist on a frequent basis.
• May stoop, kneel, or bend, on an occasional basis.
• Ability to wear personal protective equipment is required (including but not limited to, steel toed shoes, gloves, safety glasses, hearing protection, protective jacket or apron and arm guards)
• All associates working on the production floor may be required to wear